JTAG PANTEC PDF

Pantech Solutions. Online Retail store for Trainer Kits,Lab equipment’s,Electronic components,Sensors and open source hardware. This process is to assist in the repair of your Pantec receiver. There are 2 We need to Build a JTAG cable and we need to modify the receiver. To modify the. have performed the JTAG operation on my Pansat A using both Skymax and jKeys .. The first thing to do here is figure out if you have a PanTec MX or MS.

Author: Akijin Akinorn
Country: Jordan
Language: English (Spanish)
Genre: Marketing
Published (Last): 14 May 2015
Pages: 318
PDF File Size: 7.74 Mb
ePub File Size: 11.50 Mb
ISBN: 368-2-98657-263-7
Downloads: 38207
Price: Free* [*Free Regsitration Required]
Uploader: Yozshushakar

Review the Application Code Step 8: Remove the case screws and remove the top panel of the case. Jfag the Application Code Step Then we apply the auto roll flash by serial interface.

Continually check as you go as its hard to fix a miss drilled hole.

Analog Sensor Conditioning Additional content planned You will be able to solder from the points indicated in the board and run the wires to the header. Please note that in the diagram above, it looks like the wires are connected in order. Don’t put the tape on the heat sink first. Your receiver will work at this point. You will next get a warning dialog as shown below. Turn off the receiver ntag disconect the JTAG cable and replace the cover and the 5 screws.

  ABB OD 4165 PDF

Which jtag is best for pantec mx – Archive through September 25, –

Jhag here to toggle editing of individual sections of the page if possible. On the MS this is the orange wire closest to the rear of the machine on the connector. Make the wires as short as possible and keep them organized.

Do not use a soldering gun. Repeat the soldering steps just taken and your done.

PANTEC MS REPAIR

There are holes under these tabs filled with solder and this must be removed. Simply click save, and you will begin the dump process.

Generate Harmony code Step 8: Simply click the OK button to access programming functions for the the flash chip. If an error message appears, repeat the process. Next you want to add the fan. The 5 resister bank pntec below will be missing the 4th resister.

Tap the power from the wires on the connector on the board. Gently remove the receiver board from the case. Repeat the last step. The display should light up. You need the wires from pin 2,3,4,5,13,18,19,20,21,22,23,24, Append content without editing the whole page source.

Do not use a cool heat soldering iron. Factory Bin for your machine.

The air will quickly cool the board pantsc help minimize trace burning. This is repeated for DB25 Pin 3,4,5. I think cheaper is always better. If you experience problems with DCU errors in Jkeys, this will probably solve it.

  DISCOVERING THE UNIVERSE COMINS PDF

Which jtag is best for pantec mx

I have seen and read alot of crazy mod suggestions but trust me this is not that hard. Fasten the tape to the CPU and then put the heat sink on top.

You can cut the rest. In many systems, the optional TRST pin is not implemented, resulting in a four wire interface. Place the 4 LED’s on the board and organize them in such a way that you can add the other components.

That will let you know if you have your JTAG connected right. You will know this if your LED’s don’t light or light properly. Just a sec or 2 will be enough to meld the tinned end to the already solder prepared tab.

Lab4 SD card Audio Player: Do not attempt to fasten the assembly to the main board with glues or screws. Don’t forget the rear panel screw near the RCA plugs. Also put some tape on it as a precaution against shorts underneath when you attach the JTAG cable.