L Stainless Steel Sheet. ASTM A Characteristics. / L stainless steel sheet exhibits high strength, toughness and high temperature resistance. The following alloys meet the ASTM-A standard. Select an alloy for product specifications: stainless steel provides high strength and good ductility. ASTM A Standard Specification for Annealed or Cold-Worked[1] _机械 /仪表_工程科技_专业资料。ASTM A Standard.

Author: Gonos Kazralmaran
Country: Benin
Language: English (Spanish)
Genre: History
Published (Last): 28 April 2016
Pages: 64
PDF File Size: 15.75 Mb
ePub File Size: 15.2 Mb
ISBN: 870-7-37997-649-2
Downloads: 44932
Price: Free* [*Free Regsitration Required]
Uploader: Turg

Hard Elongation in 2 in. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Material Test Report and Certi?

Only annealed conditions of grades speci? Users of this standard are zstm advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. In case of dispute, the offset method of determining yield strength shall be used.

An alternative method of determining? One bend test shall be made from one end of each coil. This revision of Speci?

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. A — 03 Standard Speci? Rockwell B 95 95 Your comments are invited either for revision of this standard or for aztm standards and axtm be addressed to ASTM International Headquarters.


This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use.

Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties.

The steels shall adhere to specified chemical composition requirements.

ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

They shall be formed in different shapes such as sheets, strips, plates and flat bars. A superscript epsilon aatm indicates an editorial change since the last revision or reapproval.

The values given in parentheses are for information only. C Annealed material that naturally meets mechanical properties may be applied. B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci? This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions.

Mechanical properties such as yield strength, tensile strength, elongation, hardness, and bending shall be determined. However, in the atsm of dispute, tests shall be made by pressure.


The values obtained in this manner should not, however, be taken as the actual yield strength for 0. Link to Active This link will always route to the current Active version of the standard. The choice of test method for materials in conditions other than annealed shall be at the option of the seller.

ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

Historical Version s – view previous versions of standard. B Maximum unless otherwise indicated.

This standard has been approved for use by agencies of the Department of Defense. The specimens shall be subjected to tension test, free-bend test, and controlled-bend or V-block test. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Last previous edition approved in as A — ASTM International takes a66 position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

The values given in parentheses are for information only. Originally approved in