FIDC tracking water injection system osa User manual v4w Page 2 GETTING TO KNOW THE AQUAMIST HFS-6 osa Aquamist has been. WORKS has been using Aquamist Water Injection since We have seem them all since then and still strongly believe these are the most well thought out. Retired System Information. Below you will find technical info and original sales info for the systems. Aquamist HFS-6 Injection System. Aquamist HFS
|Published (Last):||4 July 2018|
|PDF File Size:||3.3 Mb|
|ePub File Size:||2.18 Mb|
|Price:||Free* [*Free Regsitration Required]|
The ERL electro-magnetic pump In order to find a pump that will reliably perform under the harsh environment asuamist the engine bay, we have no alternatives but to design our own. This inline valve is made of hfw-6 grade stainless steel. As seen form qauamist diagram above, the construction of the center of the pump aqkamist very similar to a bicycle pump, two valves: The special magnetic stainless armature is set in motion by strong magnetic field induced by a powerful solenoid.
Sell one like this. RACE PUMP INFO We have ruled out the widely available centrifugal pump as the pumping mechanism, because it is always coupled to a high rotational-speed drive-motor for efficiency reasons, hence it is prone to wear; further problem arises when the water inside the pump is frozen, the drive motor has to be detached from the vane by a slipping clutch arrangement so drive-motor windings cannot be damaged as a result of jamming, this led to unnecessary expenses and complicated mechanical links.
Its primary function was to regulate the water pressure during injection and idle periods set at 5 bars.
Retired System Information | Howerton Engineering
Aquamist 1s The 1s is a single stage system that consists of an ERL high-pressure electro-magnetic water pump, adjustable pressure switch, hfx-6 all the necessary hardware to form the basis of a starter kit. As the pulsed signal from the pressure switch is directly proportional to the flow of water, it can either be recorded by an on-board data acquistion system for diagnostic purposes or read by the control ECU to monitor blockage or hsf-6 jet and other faults that may arise.
Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab Add to watch list.
A high aquuamist pump with NO mechanical links, thus eliminated damages caused by jamming.
The system provides a pre-pressurized water line up to 8 bars and the flow rate is metered by our latest High speed Valve HSV. For those who want a 3-D water injection MAP but do not want to spend the time-consuming task of mapping, this system is perfect for you. The valve is terminated with water proof sealed connectors IP The ERL electro-magnetic pump is the result of a two-year intense mechanical and electronic research and development program.
In addition, it has diagnostic circuitry designed to detect blocked water-jets and cut pipes.
Refinements such as flow rate and block jet detection can easily be obtained with a minimum of signal conditioning parts, to achieve a fully integrated water injection system with diagnostic capablities. Add to watch list Add to wish list. Start of add to list layer. For additional information, see the Global Shipping Program terms and conditions – opens in a new window or tab This amount includes applicable customs duties, taxes, brokerage and other fees.
Retired System Information
In reference to the schematic diagram on the bottom of this page, the only parts that require interfacing is the HSV High Speed Valve. The color supplied with the kit is semi-translucent white, but red, yellow, green, blue and black are available on request.
San Diego, California, United States. It is normally fitted to the vacuum side of the inlet manifold 2D mode for applications where aquamiist signal throttle angle sensor or manifold absolute pressure sensor MAP sensor is available. Jet sizes from 0.
Aquamist HFS-6 Methanol/Alcohol/Water Injection System- Subaru WRX/STI Ready | eBay
A pre-pressurized system enables instant response on demand. Water is then delivered without being in contact with the drive-motor, pressure and delivery rate is regulated by internal high-tech electronic circuitry. MF2 MF2 is the brain of the system, ultimately responsible for the vital functions of metering the water delivery rate. Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab.
Estimated on or before Mon. The fixed injection rate of the HFS-1 suits this application perfectly, and with the best failsafe system in the industry, is a great choice.
Water travelling through these grooves picks up a swirling motion before leaving the small hole on the tip, causing an atomising effect, turning the water aqiamist a fine mist: Sep 20, In addition, high speed drive motor tends to suffer from burn-out under prolonged continuous running. In hard water areas, occasionally clean the filter in a small glass of diluted household lime-remover.
Peak pressure can go as high as psi! There are no mechanical links between the piston and the drive motor: The system provides a pre-pressurized water line up to 8 bars and the flow rate is metered by our High Speed Valve HSV.