2N Transistor Datasheet pdf, 2N Equivalent. Parameters and Characteristics. 2N Silicon NPN Transistor. Data Sheet. Description. Semicoa Semiconductors offers: • Screening and processing per MIL-PRF Appendix E. DATA SHEET NPN switching transistor in a TO metal package. collector- emitter voltage open base. 2N −. V. 2NA. −.
| Author: | Zulujora Tojasida |
| Country: | Somalia |
| Language: | English (Spanish) |
| Genre: | Environment |
| Published (Last): | 2 December 2009 |
| Pages: | 281 |
| PDF File Size: | 12.86 Mb |
| ePub File Size: | 7.18 Mb |
| ISBN: | 883-9-91165-437-1 |
| Downloads: | 14965 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Zumuro |
Another important thing to keep in mind, while using a transistor as switch is the base resistor. Overall it is just another small signal transistor which is commonly used in switching and amplifying circuits. So to calculate the resistor value of the base we can use the formulae. Here lets us assume the load here consumes around mA maximum so our collector current Trasistor C mA.
2N Transistor Pinout, Specs, Equivalent & Datasheet
When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. Amplifier modules like Audio amplifiers, signal Amplifier etc.
But this calculation will lead to the closest value to start with. Since transistor is of NPN the load to be switched should be connected to the collector and the emitter should be connected to the ground as show in the figure below. To make this current flow through the transistor the value of base datasgeet I B can be calculated using the below formula: To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA by using a transistor to the base pin.
2N Datasheet(PDF) – NXP Semiconductors
This resistor is connected to the base pin of the transistor to limit the current flowing through the base. However this vale will not be very accurate because the transistor will have an internal voltage drop across the dataseet current, so it mostly experimental to get the maximum current from the transistor.
Submitted by admin on 21 June Where h FE, is the current gain of the transistor which in our case datashet As we know the transistor is a current controlled device meaning, we have pass some current I B thorough the base of the transistor to turn it on. In our case for a collector current of mA we have to pass a base current of 16mA. So if you looking for an NPN transistor that 2h2219 switch loads or for decent amplification then 2N might the right choice for your project.
This stage is called Saturation Region. When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. Current flows in through collector, normally connected to load. Complete Technical Details can be found at the datasheet given at the end of this page.
2N2219 Datasheet, Equivalent, Cross Reference Search
So the value if R B will be. TL — Programmable Reference Voltage.
To make this current flow through transixtor transistor transiistor value of base current I B can be calculated using the below formula:. Where Vcc is the voltage on which the load operates and V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1. The value of this current can be calculated by the required amount of current that will be consumed by the load.
The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads transsitor consume more than mA using this transistor. The 2N is a NPN transistor and is normally used as a switch in many circuits. But it comes in a metal can package and can operate on voltages slightly higher than what a 2N can handle. Current Drains out through emitter, normally connected to ground.